logo
Conéctate con nosotros

Copper Terminal Welding Machine for Sensors with Real-Time Weld Monitoring

Información básica
Lugar de origen : Guangdong , China
Nombre de la marca : PDKJ
Certificación : CE ISO SGS
Número de modelo : Custom
Información comercial
Cantidad mínima de pedido : 1 unit
Precio : 20000-45000 USD
Embalaje estándar : Plywood Case
El tiempo de entrega : 15-30 work days
Capacidad de suministro : 100 set per month
Resumen del producto

Máquina de soldadura por resistencia de una sola estación para terminales de cobre con sensor: electrodo de cobre refrigerado por agua, sujeción neumática, arranque a dos manos y una forma de onda de corriente registrada para cada soldadura.

Descripción del Producto
Contenido

One Terminal, One Weld: A Cold Joint Never Shows Up At This Station, It Shows Up As A Bad Sensor Downstream

Application story  ·  Resistance welding of ring terminals onto copper busbars for sensor assemblies - single station, air-actuated water-cooled head, pneumatic clamping, and a current waveform recorded for every weld

Take a copper busbar and a ring terminal, lay one on the other, and weld them at a single spot. The joint is small, the surfaces are already clean, and a good weld looks exactly like a bad one - same flat face, same colour, same outline. Nothing at this station will tell you the difference. The difference appears later, as contact resistance, as heat, as a sensor that reads a little off and then a little more.

Copper Terminal Welding Machine for Sensors with Real-Time Weld Monitoring 

Sensor copper terminal welding machine: HMI and two-hand start on the upper panel, air-actuated head with water-cooled copper electrode, tooling platen below, control cabinet and industrial PC at the side

The Part: A Busbar, A Ring Lug, And A Joint You Cannot See

The workpiece is a piece of copper busbar with a ring terminal stacked on it - the terminal that will later be bolted down, the busbar that carries the sensor's signal or its supply. The two are joined where they overlap. It is a small part handled in trays, one at a time, hundreds or thousands per shift, and the weld itself is a single spot no wider than a fingernail.

That is the whole problem. There is no fillet to inspect, no weld bead to measure, no spatter pattern to read. An operator looking at the part after the stroke can see that something happened - there is a mark - but not whether the copper actually fused. Judging that by eye is how cold joints get shipped.

Copper Terminal Welding Machine for Sensors with Real-Time Weld Monitoring 

The part in hand: copper busbar with the ring terminal stacked on it, welded where the two overlap

The Head: Air-Actuated, Water-Cooled, One Spot At A Time

The upper electrode is a copper block carrying a replaceable tip, fed by two transparent water lines that run straight into it. Cooling is not an accessory on a copper welding head - an electrode that runs hot starts to pick up copper and zinc, the contact resistance climbs, and the next weld is made at a different current than the one that was set. Keeping the electrode at temperature is what keeps the weld the same from the first part of the shift to the last.

Below the part, the return path is the platen itself: a solid copper block under the tooling, large enough that the current spreads out instead of concentrating at a point under the workpiece. The press is a pneumatic cylinder on linear guides with an adjustable stroke, so force is built before the current is switched on and released only after the nugget has formed.

Copper Terminal Welding Machine for Sensors with Real-Time Weld Monitoring 

Copper Terminal Welding Machine for Sensors with Real-Time Weld Monitoring 

Head at rest, electrode above the tooling

Electrode, water lines and the copper platen

The Tooling: Pneumatic Fingers, Not The Operator's Fingers

The busbar sits on locating blocks and is held by pneumatic fingers that close before the electrode comes down. That order matters: if the part can move even a fraction of a millimetre while the force is building, the two surfaces shift against each other, the contact area changes, and the same current produces a different weld. Clamping first, pressing second, welding third is what makes the schedule repeatable.

Everything the operator does is place the part and take it out. Position comes from the tooling, so a new operator on the first day produces the same weld as the person who set the machine up.

Copper Terminal Welding Machine for Sensors with Real-Time Weld Monitoring 

Tooling from the side: pneumatic fingers and air lines around the platen, water return below

The Record: Every Weld Leaves A Waveform

The HMI on the upper panel sets the schedule - current, time, pre-press - and the machine runs it. But the part that answers the cold-joint question is the industrial PC beside it: it samples the welding current and draws the waveform of every single weld on screen, one trace per stroke. A weld that drew less current than the schedule asked for is visible as a short trace, at the moment it happens, not at final inspection.

That is the difference between a machine that welds and a machine that can prove it welded. For a part with no inspectable joint, the waveform is the only record there is - and it is kept per piece, so a batch can be traced back to the strokes that made it.

Copper Terminal Welding Machine for Sensors with Real-Time Weld Monitoring 

Operator position: HMI with current, time and pre-press settings above, the waveform monitor running on the PC at the side

Built To Stand At A Bench

The machine is one column: head, tooling, control cabinet, water circuit and air preparation in a single sheet-metal frame on levelling feet, with anti-vibration pads under them. It arrives assembled, is set down, levelled, connected to air and water, and runs - there is no separate power cabinet to site and no separate chiller to plumb in across the floor.

The working height is set for a standing operator: tray in, part in, two-hand start, part out. Status is read from the three-colour lamp on top and from the HMI, an E-stop sits where the hands already are, and the control cabinet is on the side, away from the weld zone, where it can be opened for service without reaching past the electrode.

Copper Terminal Welding Machine for Sensors with Real-Time Weld Monitoring 

Three-quarter view: head column, tooling platen, side cabinet in yellow, industrial PC and keyboard shelf

Copper Terminal Welding Machine for Sensors with Real-Time Weld Monitoring 

Copper Terminal Welding Machine for Sensors with Real-Time Weld Monitoring 

Front view in the workshop

Side view - cabinet, water and air connections

 

Copper Terminal Welding Machine for Sensors with Real-Time Weld Monitoring 

Copper Terminal Welding Machine for Sensors with Real-Time Weld Monitoring 

Machine at the bench, lamp and HMI at eye level

Working position, tooling at waist height

Shipped As One Unit

The machine travels assembled. It is wrapped, crated and loaded as a single unit, so what is uncrated at the customer's site is the machine that was run off in our workshop - not a kit that has to be re-aligned and re-commissioned on arrival. Tooling, spare electrode tips, drawings and the schedule list go with it.

Copper Terminal Welding Machine for Sensors with Real-Time Weld Monitoring 

Crated and loaded: the machine ships as one assembled unit

Machine Configuration

Item

Configuration

Station

Single station, vertical bench-top frame, standing operator

Workpiece

Copper busbar with ring terminal, joined at one spot

Welding

Resistance welding - single spot per terminal, schedule set on the HMI

Upper electrode

Copper electrode block with replaceable tip, water-cooled

Lower electrode

Solid copper platen under the tooling - current spread over a wide area

Press

Pneumatic cylinder on linear guides, adjustable stroke

Clamping

Pneumatic fingers and locating blocks; part positioned by the tooling

Control

HMI touch screen - welding current, welding time, pre-press

Monitoring

Industrial PC sampling the welding current, waveform displayed and logged per weld

Start / safety

Two-hand push buttons, E-stop on the front panel, three-colour status lamp

Cooling

Water circuit to electrode and platen, transparent return lines

Air

Filter-regulator, solenoid manifold and speed controls on the frame

Frame

Sheet-metal cabinet on levelling feet with anti-vibration pads

Services

Compressed air and cooling water at the machine; no separate chiller unit

Delivery

Wrapped and crated, shipped assembled as one unit

Electrical rating, electrode force and welding schedule are set from the terminal and the busbar thickness, and confirmed by sample welds and a pull test before shipment - they are not a fixed catalogue figure.

Where It Welds

•   Ring terminals welded onto copper busbars for sensor assemblies

•   Copper-to-copper joints where the weld is a single spot and cannot be inspected by eye

•   Small terminals and lugs handled in trays, one part per stroke

•   Parts where the visible face has to come out flat, with no spatter and no burn mark

•   Batches that need a weld record per piece rather than a visual check at the end

•   Copper and tinned copper assemblies in sensors, battery packs and control harnesses

Tooling is cut for the terminal: locating blocks, finger positions and electrode tip are made from your part drawing, and we weld samples from your production batch before the machine is released.

From Part To Machine

01   Terminal and busbar drawing, material and stack-up review

02   Sample welds on your parts, with waveform check and pull test

03   Electrode, tooling and schedule proposal

04   Machine design - head, press, platen, clamping and cabinet layout

05   Frame, head, water circuit and pneumatic build

06   Controller and HMI integration, waveform monitoring set up

07   Assembly, run-off and waveform review on customer parts

08   Crating and shipment as one assembled unit

09   On-site commissioning, operator training, after-sales support

Talk to Pudian Technology

Guangdong Pudian Automation Technology Co., Ltd builds resistance and laser welding equipment in-house - transformers, controllers, electrodes, fixtures and complete machines - one team, one solution. Welding a terminal where a cold joint would be invisible? Send us the part and the stack-up, and we will weld samples and show you the waveform before you commit.

Guangdong Pudian Automation Technology Co., Ltd

WhatsApp / Tel: +13613793248    Email: jay@gd-pw.com

Website: https://www.spotlaserwelding.com/

Address: 1-2F, Building 3, Qichen Industrial Park, No. 26 Luxi 1st Road, Liaobu Town, Dongguan City, Guangdong Province, China


Envíanos un Consulta
Le responderemos dentro de las 24 horas.
Detalles de las consultas
Información del contacto